YGD Light Rod Hydraulic Cylinder

YGD light rod hydraulic cylinder is the company’s advantage products, manufacturing experience, mature technology, and cost-effectiveness. The cylinder of the light rod adopts a seamless steel pipe. Different working pressures allow the selection of steel tubes with different wall thicknesses. The inner diameter machining precision is high, the structure is compact, the weight is light, and the installation and connection methods are various. It has the advantages of good low-speed performance, stable buffer performance, and a pressure range of 3.5-17MPA, and it is widely used in machine tools, textiles, plastics, agricultural machinery, and equipment hydraulic systems.

Technical Specification Of YGD Light Rod Hydraulic Cylinder:

1, The use of pressure 5Mpa the following is recommended to use our factory standard low-pressure tie rod hydraulic cylinder, short processing cycle, cost-effective:
2. Minimum pressure: According to the specific application, a particular minimum force is required to ensure the function of the hydraulic cylinder. When there is no load, the recommended minimum pressure of a single-rod hydraulic cylinder is 1MPA.
3, hydraulic cylinder installation: only allow in the case of no pressure, install the hydraulic cylinder, and screw the piston rod end into the machine.
4, treatment agent: no special instructions; The hydraulic cylinder uses a grey primer.
5. Limited by stroke length, cylinder diameter, and rated working pressure, the YGD series tie rod hydraulic cylinder is usually suitable for stroke ≤1.5m, cylinder diameter ≤250mm, and rated pressure PN≤21MPa.
If the cylinder diameter is too large, the rated pressure is too high, or the stroke is too long, it is recommended to use a welding structure;
1) When the rod length is too long, it is easy to deviate during installation, resulting in leakage of the cylinder end.
2) When the inner diameter of the cylinder is too large, or the rated pressure is too high, due to the disassembly problem of the radial size arrangement, the diameter of the tie rod is limited, resulting in the tensile stress of the tie rod may exceed the yield limit.

YGD Light Rod Hydraulic Cylinder:

(1) TB Type Four Rod Hydraulic Cylinder

(2) TC Type Four Rod Hydraulic Cylinder

(3) TD Type Four Rod Hydraulic Cylinder

(4) Front Cover Rectangular Flange Four Rod Hydraulic Cylinder

(5) Rear Cover Rectangular Flange Four Rod Hydraulic Cylinder

(6) C Type Seat Four Rod Hydraulic Cylinder

(7) Rear Single Earring Four Rod Hydraulic Cylinder

(8) Rear Double Earring Four Rod Hydraulic Cylinder

(9) Rear Earring With Spherical Bearing Four Rod Hydraulic Cylinder

(10) Front Cover Trunnion Four Rod Hydraulic Cylinder

(11) Rear Cover Trunnion Four Rod Hydraulic Cylinder

(12) Middle Fixed Trunnion Four Rod Hydraulic Cylinder

(13) Double Piston Rod Hydraulic Cylinder

Technical Parameter Of Light Rod Hydraulic Cylinder:

YG C-D /d E × 200-TB 4 1 1-y *
C-type :C= differential cylinder; D= constant speed cylinder
D/ D – Cylinder diameter/rod diameter
E – Pressure grade :C=7MPa; E = 16 mpa; D = 21 mpa
200 – Stroke mm
TB – Installation mode :TB= Pull rod extends out of front cover end; TC= pull rod extension back cover end; TD= extension at both ends of the tie rod; JJ= front cover rectangular flange; HH= rear cover rectangular flange; C= side lug (type C seat); B= posterior monaural; BB= back stud; SBd= Back earrings with spherical bearings; D= front cover trunnion; DB= rear cover trunnion; DD= middle fixed trunnion
4 – piston rod end mode :3= non-standard piston rod end; 4= piston rod end external thread; 9= piston rod end internal thread
1-oil connection mode :1= inch internal thread; 2= metric internal thread
1 – Oil port position (see the following figure from the piston rod end)
1 – Buffer position :1= buffer at both ends; 2= no rod-cavity buffer; 3= buffer with rod cavity; 4= No buffer at both ends
Y – The length of the piston rod is measured in millimeters. Write with words. Leave this option blank

Ygc Light Rod Hydraulic Cylinder Characteristics:

Ygc Light Rod Hydraulic Cylinder Installation Method Selection Instructions:

1, Tie rod extension mounting (TB, TC, TD) cylinders are suitable for linear force transmission applications, especially useful in the case of limited space. Cylinder head-end rod mounting is best suited for compression. When the piston rod is stretched, the installation method of the end of the cylinder head should be specified. A cylinder with a pull rod extending from both ends can be fixed to a machine component from either end, while the free end of the cylinder can support a bracket or switch.

2, Fflange-mounted (JJ, HH) cylinders are also suitable for linear force transmission applications. For compression use, cylinder head installation is the most convenient. The cylinder head shall be specified to be installed where the main load causes the piston rod to be stretched.

3, Mounted on the tripod (C) cylinder, does not absorb the force on its center line. As a result, the pressure the cylinder applies creates a tipping moment that attempts to flip the cylinder around the mounting bolt. Therefore, it is essential to secure the cylinder firmly to the mounting surface and guide the load effectively so that the lateral load is not applied to the rod seal and piston guide ring.

4. Hinged cylinders (B, BB, SBd) can absorb the force on their center line and are applied where the machine parts move along the curve. If the bending path of the piston rod is in a plane, two modes of BB and B can be used to fix the cylinder of the earring. For uses where the piston rod will travel along a path on either side of the actual plane of motion, SBd with spherical bearings is recommended.

5, Trunnion mounting (D, DB, DD) cylinders are designed to absorb the force on their center line. They are suitable for tensile (tension) or compression (thrust) purposes and can move machine members along curved paths within a single plane. The trunnion pins are designed for shear loads only and should withstand minimal bending stress.

Aptidão e capacidade da fábrica:

(1) Montagem

Temos uma plataforma de montagem de pesquisa e desenvolvimento independente de primeira classe. A oficina de produção de cilindros hidráulicos tem quatro linhas de montagem semiautomáticas de cilindros de elevação e uma linha de montagem automática de cilindros de inclinação, com uma capacidade de produção anual projetada de 1 milhão de peças. A oficina de cilindros especiais é equipada com várias especificações de um sistema de montagem de limpeza semiautomática com uma capacidade de produção anual projetada de 200.000 peças e equipada com famosos equipamentos de usinagem CNC, um centro de usinagem, um equipamento especial de processamento de cilindros de alta precisão, uma máquina de solda robotizada, uma máquina de limpeza automática, uma máquina de montagem automática de cilindros e uma linha de produção de pintura automática. O equipamento crítico existente é de mais de 300 conjuntos (conjuntos). A alocação ideal e o uso eficiente dos recursos do equipamento garantem os requisitos de precisão dos produtos e atendem às necessidades de alta qualidade dos produtos.

(2) Usinagem

A oficina de usinagem é equipada com um centro de torneamento de trilho inclinado personalizado, um centro de usinagem, uma máquina de brunimento de alta velocidade, um robô de soldagem e outros equipamentos relacionados, que podem lidar com o processamento de tubos de cilindros com diâmetro interno máximo de 400 mm e comprimento máximo de 6 metros.

(3) Soldagem

(4) Pintura e revestimento

Com linhas de revestimento de tinta à base de água automáticas de cilindros de pequeno e médio porte, para obter carregamento e descarregamento automáticos de robôs e pulverização automática, a capacidade projetada é de 4.000 peças por turno;
Também temos uma linha de produção de tinta semiautomática para cilindros grandes, acionada por uma corrente elétrica, com capacidade de projeto de 60 caixas por turno.

(5) Testes

Temos instalações de inspeção e bancos de teste de primeira classe para garantir que o desempenho do cilindro atenda aos requisitos.

We are one of the best heavy rod hydraulic cylinder manufacturers. We can offer comprehensive heavy rod hydraulic cylinder stock. We also provide corresponding caixas de câmbio agrícolas. Exportamos nossos produtos para clientes em todo o mundo e conquistamos uma boa reputação devido à qualidade superior de nossos produtos e ao serviço pós-venda. Convidamos clientes nacionais e estrangeiros a entrar em contato conosco para negociar negócios, trocar informações e cooperar conosco!